Zero Speed Switch Sensor, ZS09P

Phone: 813-262-0680 Send Email

Related Links

Dimensions (in inches):

Zero Speed Switch Sensor ZS09P Dimensions

Wiring Connections:

Zero Speed Switch System
Utilizing Axial Magnetic Target Disk

Zero Speed Switch System
Utilizing Radial Magnetic Target Disk

Zero Speed Switch System
Utilizing Geartooth Wheel

Features and Benefits

Over speed, under speed and zero speed sensing
Senses magnetic and ferrous targets
Self-contained unit incorporates sensor and relay
Isolated outputs with 5 amp switching capacity
Diagnostic indicators
Not rotation direction sensitive
Relay latch option
Operating voltages: 6-24 VDC and 120 VAC
Use outdoors or in wash down areas
Prompt alert for stalled or zero speed condition
Easy interface to existing systems
Helps prevent equipment damage and material spoilage

Overview

The ZS09P Zero Speed Switch Sensor is a self-contained device that combines sensor and switch for use in over speed, under speed, or zero speed applications. It senses magnetic and low carbon ferrous targets. Outputs are isolated and can be easily integrated with any controller or existing system. It is about the size of a prox switch, but incorporates intelligent speed sensing circuitry not found in simple on/off devices. Use the ZS09P Zero Speed Switch Sensor for switching control circuit loads or logic inputs (PLC, DCS, etc.).

Operation

When motion is either detected or reaches setpoint (depending upon application), the relay output changes state. It remains in this state until under speed or zero speed condition occurs (depending upon application).

Specifications

Power Requirements:
6-24 VDC, 50/60 Hz (for Part No. ZS09P-D)
120 VAC, 50/60 Hz (for Part No. ZS09P-120)

Current Draw: 50 mA

Fuse: Internal 1/2 Amp non-replaceable fuse

Relay Output: (specify when ordering)
SPDT Form 'C' dry relay contact (Normally Open/Closed)
SPST Normally Open
SPST Normally Closed

Contact ratings:
5 A, 240 VAC
5 A, 30 VDC
Vibration resistance (function) NO/NC contact >15/5 g
Shock resistance (destruction) >100 g

Operating Frequency:
Hall Effect and Inductive (Geartooth): 10 kHz maximum
Hall Effect Only: 25 kHz maximum

Sensing Distance (Gap):
1/16" to 1/8" using Geartooth Wheel, Bolt Head, etc.
1/8" to 1/4" using Magnetic Ring.
1/8" to 5/8" using Magnet or Magnetic Disk.
(Magnetic target sensing distance based on Phares Electronics, LLC magnetic disks and magnet types).

Minimum Geartooth Sizes:
1/8" geartooth length, width, depth and gap.

Geartooth Material: Low carbon steel

Operating Temperature: -40°F to 140°F

Weight: 6 oz.

Cable: 4 ft., 6 conductor, 22 AWG, unshielded
(Custom cable lengths available.)

See the Ordering Information table for part numbers and corresponding specifications.

Quick Technical Application Notes

Ordering Information
Zero Speed Switch Sensor, ZS09P

Part Number	Description	Relay Output	Contact Rating	Load Type	Speed Switch Type	Setpoint	Target (Sold Separately)
ZS09P1-D ZS09P2-D ZS09P3-D	Zero Speed Switch Sensor, 6-24 VDC Zero Speed Switch Sensor, 6-24 VDC Zero Speed Switch Sensor, 6-24 VDC	N.O./N.C. N.O. N.C.	5 A 5 A 5 A	Control Circuit or Logic Input	Self-Contained Sensor	Adjustable or Fixed Setpoint	Magnet, Magnetic Disk, Magnetic Ring, Split Coupling, Bolt Head, Gear Tooth Wheel, or other magnetic or ferrous target.
ZS09P1-120 ZS09P2-120 ZS09P3-120	Zero Speed Switch Sensor, 120 VAC Zero Speed Switch Sensor, 120 VAC Zero Speed Switch Sensor, 120 VAC	N.O./N.C. N.O. N.C.	5 A 5 A 5 A	Control Circuit or Logic Input	Self-Contained Sensor	Adjustable or Fixed Setpoint	Magnet, Magnetic Disk, Magnetic Ring, Split Coupling, Bolt Head, Gear Tooth Wheel, or other magnetic or ferrous target.

How to Order

Order direct from Phares Electronics, LLC. We accept Visa and Mastercard. Our phone number is (813) 262-0680. When ordering, please specify the following:

Stock Number
Relay Latch option if needed. The maximum time delay is 60 seconds.
For example, a 5 second Latch would change part number ZS09P1-120 to ZS09P1L05-120.
Adjustable or Fixed Relay Setpoint.
Magnetic Disk or other target. When using a geartooth wheel, please specify number of teeth on wheel.

For assistance matching the ZS09P Zero Speed Switch Sensor and Magnetic Disk correctly for your application, please call (813) 262-0680 or email Sales@PharesElectronics.com.

Top of page